Bert Simonovich's Design Notes

Innovative Signal Integrity & Backplane Solutions

PCB Laminate Construction

leave a comment »

Present day FR4-style laminates used for PCB fabrication rely on woven glass fiber yarns to maintain the structural integrity of the finished product. These yarns are made up of electronic or E-Glass material. Because it is the same glass used in everything from Corvette bodies to boat hulls, it is a very inexpensive reinforcement material. NE-Glass has improved electrical and mechanical performance over E-Glass. It is used for higher performance laminate products such as Park Nelco 4000-13SI.

imageThe table on the left shows five of the most common fiberglass styles used for laminate construction today. When glass fiber yarns are woven into fabric, the “Warp” yarns run the length of the roll, while the “Fill or Weft” yarns run the width. Yarn count refers to the number of warp threads per inch by the number of fill threads per inch.

Prepreg is the term we commonly use for a weave of glass fiber yarns pre-impregnated with resin which is only partially cured. The glass to resin thickness ratio defines the overall thickness of a prepreg mat. You can see from the table above, the typical resin content is a function of the thread count and yarn diameter. imageFor example, the figure on the far left illustrates styles like 106 and 1080 having smaller diameter yarns and  higher resin content. The right hand figure is indicative of yarns with larger diameter and lower resin content like style like 2116 or 7628.

When copper foil is attached to one or both sides of fully cured prepreg mats, the finished laminated panel is called a core. Both cores and prepreg mats are available in various panel sizes and thicknesses.

There are several different kinds of resin systems in use today to form prepreg and cores. The general specification FR4 is the most common. It refers to a specific fire-retardant level rather than specific resin chemistry. Since you have a choice of many laminates that meets the FR4 fire specification, there is no such thing as “standard FR4”. That being said, most of us consider “standard FR4” to mean a laminate having a typical dielectric constant (Dk) of about 4.3 and dissipation factor (Df) of 0.020 – 0.025 at 1MHZ and 50% resin content.

Each family of resin systems have their unique electrical and mechanical characteristics depending on the fiberglass style and resin chemistry. For example, Nelco 4000-6 at 50% resin content has a typical Dk of 4.0 and Df of 0.023 at 2.5GHz. A higher performance resin system like Nelco N4000-13 on the other hand, has a Dk of 3.7 and Df of 0.009 for the same resin content and frequency.  This tells us two things:

  1. A lower Dk means we can ultimately achieve an overall thinner board for the same characteristic impedance.
  2. A lower DF means less high frequency attenuation allowing us to run at a higher bit rate or have longer traces.

When designing your board stack-up, it is best to refer the manufactures data sheet for exact values. The Park Electrochemical Corp. (Nelco) website is an excellent resource to explore when trying to decide on the best dielectric material to use for your next high-speed design.

Written by Bert Simonovich

December 14, 2010 at 9:13 pm

Introduction

leave a comment »

Welcome to my Blog! I am Bert Simonovich, founder and president of Lamsim Enterprises Inc. I graduated in 1976 from Mohawk College of Applied Arts and Technology in Hamilton, Ontario, Canada as an Electronic Engineering Technologist. I started my consulting business after working 32 years at Bell Northern Research/Nortel. Throughout my career, I have held a variety of hardware design engineering positions and pioneered several advanced technologies into products. Currently I offer innovative signal integrity and backplane solutions as a consultant.

From as far back as I can remember, I was always interested in how things worked. I would often take things apart just to see what was inside; -not always successful in putting them back together again though ;-o.  I was always fascinated with electricity and electronics. When I was about 10 or 11, I was mystified with how telephones worked. After reading about Alexander Graham Bell in a booklet published by The Bell Telephone Company of Canada, I became inspired to buy a pair of old push to talk handsets from a local army surplus store. I experimented with them using a drycell battery and lamp cord wire. When I finally was able to get two-way communications, it seemed like magic. I knew right then what my career choice would be.

I have been fortunate throughout my career to have been a part of and contribute to some of the technology that enable the gadgets we enjoy today. I have met and worked with many smart and talented individuals who took the time to unselfishly share their knowledge and experience.

And now, after all this time, the passion I had as kid to learn and understand new things is still there. Except now, like cradling a fine glass of wine, I am able to slowly swirl it around, sip it and savor the taste. This blog is about sharing some of that passion. It will cover a range of topics from signal integrity, PCBs, backplane design, circuit modeling, simulation tools and other practical engineering solutions. I hope you find my posts interesting and get inspired to explore them further on your own.

Thanks for visiting. I invite you to constructively comment and share your own thoughts and experiences as well.

Written by Bert Simonovich

December 13, 2010 at 12:30 pm